1.給料機在使用過程中需要檢查如下內容
(1)檢查給料機和激振器振幅，振幅不得超過給料機設計極限值。
(2)檢查主振橡膠彈簧是否有開裂。
(3)檢查隔振彈簧是否有開裂。
(4)檢查各緊固螺栓是否有鬆動。
(5)檢查電動機運轉中是否有異常聲響。
2.給料機運行初期一周內，必須每天檢查並擰緊各連接螺栓，一周後，可隔一天檢查並擰緊一次，直到設備運行穩定為止。
3.電機維修與保養按電機使用說明書進行。
4.振動給料機操作規程
(1)給料機安裝與振動電機接線後，進行全麵安全檢查，以避免開機後發生人身與設備事故，確認各處螺栓緊固，設備可靠接地，方可開機。
(2)給料機不宜空載運轉時間過長，30分鍾以內停機後，要將全部螺栓緊固一次，以後要定期檢查，發現鬆動及時緊固，確保振動電機與設備的牢固連接。
(3)在調整給料量時，可以通過以下方法進行。
a.調整加大振動電機的激振力。
b.調整槽體吊掛的長度，使槽體沿下料方向往下傾斜，傾斜角度在通常情況下0~-140範圍內，按不同物料的自然安息角，以不自動跑料為原則。
英文如下：
1 feeder in use process must always check the following
(1) examined the feeder and the vibration amplitude, amplitude limit value shall not exceed the feeder design.
(2) check the main vibration rubber spring if there is crack.
(3) check the isolation spring if there is crack.
(4) check the fastening bolts are loose.
(5) to check whether there is abnormal sound of motor in operation.
2 feeder in early operation period of a week, must be inspected daily and tighten all the connecting bolts, a week later, can be every day to check and tighten again, until the stable operation of equipment.
3 Motor repair and maintenance according to the motor with the instruction manual.
4 double mass vibration feeder operation procedures
(1) feeder mounted and vibration motor wiring, type XZG to conduct a comprehensive safety inspection, to avoid the boot after the personal and equipment accident, confirmed all bolts, reliable equipment grounding, can boot.
(2) feeder for no-load running time is too long, 30 minutes after shutdown, will all bolt a, later to be checked regularly, ensure timely found loose fastening, the vibrating motor and equipment connected.
(3) in the adjustment of feeding amount, can adopt the following methods.
a adjusted to increase the exciting force of the vibrating motor.
b Adjustment tank hanging length, the trough along the feeding direction slope down, tilted at the angle of typically 0 - 140 range, according to the different material natural angle of repose, to automatically run the material principle.

(圖/文www.changrong-jx.com)